- Novo

Esta é uma placa de desenvolvimento que combina um processador dual-core de 32 bits, com conectividade Wi-Fi de 2,4GHz e Bluetooth 5 (BLE). Ela possui 16MB de Flash e 8MB de PSRAM integrados. A placa destaca-se pelo seu ecrã tátil capacitivo de 4,3 polegadas com resolução de 800×480 e suporte a 5 toques em simultâneo, permitindo a execução fluida de interfaces gráficas, como o LVGL. Além disso, oferece várias interfaces periféricas, incluindo CAN, I2C e RS485, facilitando o desenvolvimento rápido de aplicações de interface homem-máquina (HMI) e outras aplicações baseadas no ESP32-S3.
Se quiseres saber mais sobre este produto, consulta a sua Wiki Page.
DESCRIÇÃO EM PORTUGUÊS BREVEMENTE DISPONÍVEL
Se tiver alguma dúvida neste produto não hesite em contactar-nos.
*Atenção: as imagens são meramente ilustrativas.
ESP32-S3-Touch-LCD-4.3B is a microcontroller development board with 2.4GHz WiFi and BLE 5 support, integrates high-capacity Flash and PSRAM. Onboard 4.3inch capacitive touch screen can smoothly run GUI programs such as LVGL. Combined with various peripheral interfaces, suitable for the quick development of the HMI and other ESP32-S3 applications
Equipped with Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (LE), with onboard antenna
Built in 512KB SRAM and 384KB ROM, with onboard 16MB Flash and 8MB PSRAM
Onboard 4.3inch capacitive touch display, 800×480 resolution, 65K color
Supports capacitive touch control via I2C interface, 5-point touch with interrupt support
Onboard voltage regulator, supports 7~36V wide range power supply
Onboard RTC chip and rechargeable battery to ensure time data is not lost when power loss
Onboard CAN, RS485, I2C interface, TF card slot, MX1.25 2P battery header, and digital isolated IO interfaces, etc.
Supports passive and active digital input, with bi-directional optocoupler isolation
Supports digital output with optocoupler isolation, provides higher driving capability with up to 450mA sinking current
Onboard LED indicators for indicating the power and battery recharging status
Supports flexible clock, module power supply independent setting and other controls to realize low power consumption in different scenarios
Excellent display performance, 160° wide viewing angle
supports touch function with I2C interface, 5-point touch for flexible operation and smooth multi-point UI interaction
Supports the expansion of multiple peripherals via CAN, RS485, I2C and isolated IO interfaces
Comes with two types of screw terminals, allowing for bottom or back wiring, which is more convenient to integrate into various application scenarios such as DIN rail or embedded devices
Back Wiring
Back Wiring
ESP32-S3-WROOM-1-N16R8
The SoC with WiFi and Bluetooth, up to 240MHz operating frequency, integrated 8MB PSRAM and 16MB Flash
TF card slot
USB Type-C port
BOOT button
Press and hold while powering on for program burning
RESET button
Optocoupler isolation
Touch panel connector
4.3inch display panel connector
RS485 and CAN terminal resistors selection
close by default
Battery power supply ON/OFF
3.7V single lithium battery MX1.25 header
Status Indicators
DONE: Lithium battery charging completed indicator
CHG: Lithium battery charging indicator
PWR: Power supply indicator
(the CHG will blink and DONE will light on when connecting with DC power supply and without lithium battery connected or battery switch is OFF)
7-36V DC power supply terminal
I2C interface terminal
VOUT pin output 5V/3.3V (switching by onboard resistor)
CAN interface terminal
RS485 interface terminal
Digital output
5~36V, open-drain output, output load: 450mA per channel (MAX)
Input signal common terminal
NC: dry contact passive input
Connect to power supply positive: digital input low active, for NPN wet contact active input, 5V-36V DC
Connect to power supply negative: digital input high active, for PNP dry contact active input, 5V-36V DC
Digital input
5~36V, supports passive / active input (NPN or PNP)
* for reference only, the lithium battery is NOT included.
* for reference only, the rail bracket, wall bracket and monitor arm are not included.
The mounting hole spacing on the back of the case is 75mm.
Support software and hardware customization - Including hardware interface, LOGO, label, case and web page, etc.
Wiki: www.waveshare.com/wiki/ESP32-S3-Touch-LCD-4.3B
Weight: 0.149 kg
ESP32-S3-Touch-LCD-4.3B-BOX x1
Produtos Associados
Esta é uma placa de desenvolvimento que combina um processador dual-core de 32 bits, com conectividade Wi-Fi de 2,4GHz e Bluetooth 5 (BLE). Ela possui 16MB de Flash e 8MB de PSRAM integrados. A placa destaca-se pelo seu ecrã tátil capacitivo de 4,3 polegadas com resolução de 800×480 e suporte a 5 toques em simultâneo, permitindo a execução fluida de interfaces gráficas, como o LVGL. Além disso, oferece várias interfaces periféricas, incluindo CAN, I2C e RS485, facilitando o desenvolvimento rápido de aplicações de interface homem-máquina (HMI) e outras aplicações baseadas no ESP32-S3.
Se quiseres saber mais sobre este produto, consulta a sua Wiki Page.